Hardware catalog
Search development boards, chips, and modules by model, alias, or order code.
Product comparison
| Arduino Nano ESP32 (Remove) | Raspberry Pi Pico 2 (Remove) | Raspberry Pi Pico W (Remove) | M5Stack AtomS3 (Remove) | |
|---|---|---|---|---|
| Flash | — | |||
| VSYS input range | — | — | — | |
| VIN input range | — | — | — |
Search results (45)
- Boardadafruit
Adafruit Feather ESP32-S3
Adafruit Feather ESP32-S3: the standard Feather header around an ESP32-S3 mini-module: 28 through-holes in two columns, JP1 left (16 holes, pin 16 RESET at the top, pin 1 TXD0/GPIO43 at the bottom) and JP3 right (12 holes, pin 1 VBAT at the top, pin 12 SDA at the bottom), NeoPixel on GPIO33 (power-gated by GPIO21), I2C on GPIO3/4 with a STEMMA QT connector switchable through GPIO7, MAX17048 fuel gauge, native USB-C. Three SKUs (5323/5477/5885) share one schematic.
Chip · ESP32-S3 - BoardArduino
Arduino Nano ESP32
Arduino Nano ESP32 (ABX00083/ABX00092): a Nano form factor board with a soldered u-blox NORA-W106-10B module embedding the ESP32-S3, USB-C, 16 MB on-board flash, 8 MB PSRAM in the module, and dual pin numbering (silkscreen Dn/An vs native GPIO) with the complete JP1/JP2 mapping.
Chip · ESP32-S3Replace selection - BoardArduino
Arduino UNO R4 WiFi
Arduino UNO R4 WiFi (ABX00087): the main microcontroller is a Renesas RA4M1 (Arm Cortex-M4, 5 V); a soldered ESP32-S3-MINI-1-N8 handles Wi-Fi 4 / BLE 5 as a 3.3 V secondary MCU. USB-C, 12x8 LED matrix, 12-bit DAC on A0, CAN on D13/D10.
Chip · Renesas RA4M1 - Boarddfrobot
DFRobot Beetle RP2350
DFRobot Beetle RP2350 (DFR1188): a 25 x 20.5 mm RP2350A board with two 8-pad edge columns J3/J4 carrying 11 GPIO (Serial1 on D0/D1 = chip UART0, Serial2 on D8/D9 = chip UART1, I2C on D4/D5, SPI0 on D16/D18/D19, A0/A1 on D26/D27), SWD pads TP3/TP4/TP5, LED on IO25, user button SW1 on QSPI_SS, reset SW2 on RUN, 0.5 A Li-po charging, 2 MB flash.
Chip · RP2350 - BoardEspressif
ESP32-C3-DevKitM-1
Official Espressif ESP32-C3-DevKitM-1 board record: single V1.0 board (schematic-dated 2020-09-15) with MINI-1/-1U modules, J1/J3 15-pin headers, RGB LED on GPIO8, USB-to-UART bridge and every published field with its fixed official source.
Chip · ESP32-C3 - BoardEspressif
ESP32-C6-DevKitC-1
Official Espressif ESP32-C6-DevKitC-1 board record: v1.1/v1.2 revisions with PW batch changes, WROOM-1/-1U modules, the two USB Type-C ports and their different roles, J1/J3 16-pin headers and every published field with its fixed official source.
Chip · ESP32-C6 - BoardEspressif
ESP32-C6-DevKitM-1
Official Espressif ESP32-C6-DevKitM-1 board record: ESP32-C6-MINI-1/-1U module (C6FH4, 4 MB flash in package), dual Type-C ports (native USB Serial/JTAG + UART bridge), RGB LED on GPIO8, five strapping pins, and the complete J1/J3 mapping (30 contacts) with fixed official sources.
Chip · ESP32-C6 - BoardEspressif
ESP32-DevKitC
Official Espressif ESP32-DevKitC board record: V2/V4 revisions, 32E/32UE/VE/VIE ordering variants, WROVER GPIO16/17 condition, complete J2/J3 header mapping and every published field with its fixed official source.
Chip · ESP32 - BoardEspressif
ESP32-S3-DevKitC-1
Official Espressif ESP32-S3 evaluation board: revision differences (v1.0/v1.1), ordering variants, J1/J3 pin headers and every published field with its fixed official source.
Chip · ESP32-S3 - BoardEspressif
ESP32-S3-DevKitM-1
Official Espressif ESP32-S3-DevKitM-1 board record (end-of-life): ESP32-S3-MINI-1/-1U module (S3FN8, 8 MB flash in package), dual 22-pin headers (44 contacts), Micro-USB bridge plus the native USB port (guide names it OTG; the chip runs USB Serial/JTAG or OTG over the shared PHY), RGB LED on GPIO48, and the recommended replacement path.
Chip · ESP32-S3 - Boardlilygo
LILYGO T-Display-S3
LILYGO T-Display-S3: ESP32-S3 board with an on-board 170x320 ST7789 LCD on a parallel bus (BL 38, D0-D7 = 39/40/41/42/45/46/47/48, RST 5, CS 6, DC 7, WR 8, RD 9), touch INT 16 / RES 21, both 12-position headers fully mapped (P1/P2), and GPIO15 as the peripheral power control that must be HIGH on battery power.
Chip · ESP32-S3 - Boardlolin
LOLIN C3 mini
LOLIN/WEMOS C3 mini: a 34.3 x 25.4 mm ESP32-C3FH4 board (RISC-V 160 MHz, 4 MB in-package flash) with 12 GPIO on 16 edge pads in two columns (J2 left: EN/3/2/1/0/4/5/3V3; J3 right: TX/RX/10/8/7/6/GND/VBUS; silkscreen uses bare GPIO numbers), one WS2812B RGB LED, USB Type-C, download mode via Button 9 + Reset, 3.3 V logic and D1-mini-shield compatibility. Current schematic V2.1.0. Not the 'C3 SuperMini'.
Chip · ESP32-C3 - Boardm5stack
M5Stack AtomS3
M5Stack AtomS3 (C123): a 24x24 mm ESP32-S3 board with a 0.85-inch GC9107 LCD (MOSI G21, SCK G17, CS G15, RS G33, RST G34, BL G16), an MPU6886 IMU at 0x68 sharing the I2C bus on IO38=SDA / IO39=SCL, two bottom edge columns (J3 left: 3V3/G5/G6/G7/G8; J4 right: G39/G38/5V/GND) and one HY2.0-4P port (J6).
Chip · ESP32-S3Replace selection - BoardSTMicroelectronics
NUCLEO-F401RE
STMicroelectronics NUCLEO-F401RE board record: STM32F401RET6 in LQFP64, Arduino Uno V3 headers CN5/CN6/CN8/CN9, 2x19-pin ST morpho connectors CN7/CN10, SWD connector CN4, complete 114-contact mapping with every field tied to UM1724 Rev 17.
Chip · STM32F401RE - BoardSTMicroelectronics
NUCLEO-G071RB
STMicroelectronics NUCLEO-G071RB board record (MB1360): STM32G071RB Cortex-M0+ at up to 64 MHz with 128 KB flash / 36 KB SRAM, Arduino Uno V3 headers CN5/CN6/CN8/CN9, 2x19-pin ST morpho connectors CN7/CN10, ST-LINK SWD jumper area CN4 and the physically 6-pin SWD connector CN11 (5 signals + reserved SWO). All 118 contacts mapped with the C02 schematic as adjudicating source.
Chip · STM32G071RB - BoardRaspberry Pi
Raspberry Pi Pico
Raspberry Pi Pico board record: RP2040 with 2 MB flash, no module layer, complete 40-pin J1/J2 header mapping, internal-function GPIOs and every published field with its fixed official source.
Chip · RP2040 - BoardRaspberry Pi
Raspberry Pi Pico 2
Raspberry Pi Pico 2 board record: RP2350A with 4 MB flash, hardware/software compatible with Pico, same 40-pin layout, complete J1/J2 header mapping and every published field with its fixed official source.
Chip · RP2350Replace selection - BoardRaspberry Pi
Raspberry Pi Pico 2 W
Raspberry Pi Pico 2 W board record: RP2350 with Wi-Fi and Bluetooth via the on-board CYW43439 radio, 4 MB flash, the same 40-pin J1/J2 layout as the Pico W, LED on the radio chip instead of GP25, and every published field with its fixed official source.
Chip · RP2350 - BoardRaspberry Pi
Raspberry Pi Pico W
Raspberry Pi Pico W board record: RP2040 with Wi-Fi and Bluetooth via the on-board CYW43439 radio, 2 MB flash, the same 40-pin J1/J2 layout as the Pico, LED on the radio chip instead of GP25, and every published field with its fixed official source.
Chip · RP2040Replace selection - BoardSeeed Studio
Seeed Studio XIAO ESP32C3
Seeed Studio XIAO ESP32C3: a 21 x 17.8 mm third-party board for the ESP32-C3 with 14 edge pads in two columns (left D0-D6, right 5V/GND/3V3/D10-D7), back-side BAT and JTAG pads, the bundled external U.FL antenna, Li-ion charging, and Reset/Boot buttons. A Seeed board, not an Espressif DevKit.
Chip · ESP32-C3 - Boardsparkfun
SparkFun Thing Plus ESP32-S3
SparkFun Thing Plus ESP32-S3 (WRL-24408): ESP32-S3R2 N4R2 module on a Feather-compatible board with 28 physical PTH positions carrying 21 GPIO (all silkscreen names mapped to chip IOs from the U10 schematic symbol), Qwiic on IO8/IO9, microSD on SDIO-4 (IO34/38/39/40/47/33), MCP73831 charging + MAX17048 fuel gauge, switchable 3.3V_P rail. The silkscreen 'GPIO0' pad is chip IO21, not IO0.
Chip · ESP32-S3 - BoardWaveshare
Waveshare ESP32-S3-Zero
Waveshare ESP32-S3-Zero board record (SKU 25081/25517, ESP32-S3FH4R2): 4 MB stacked flash + 2 MB Quad SPI PSRAM (datasheet v2.2 Table 1-1, PDF p.13; the vendor page's Octal wording noted), WS2812 RGB on GPIO21, native-USB Type-C with no bridge chip, GPIO33~37 not led out on this PCB, and the pad table in its real grouping: 18 edge + 3 front-inner + 8 back-inner.
Chip · ESP32-S3 - ChipEspressif
ESP32
Espressif ESP32 classic SoC family: dual LX6 cores, 2.4 GHz Wi-Fi and Bluetooth in the chip; what depends on the module and board, and how to start developing.
- ChipEspressif
ESP32-C3
Espressif ESP32-C3 SoC: single RISC-V core with 2.4 GHz Wi-Fi and Bluetooth Low Energy on chip; strapping pins GPIO2/8/9; what depends on the module and board, and how to start developing.